By admin
http://www.cwhdallas.com/jack-input/
Jack Input
| Account limit of 2000 requests per hour exceeded. |
Using a Mixer Insert Jack as a Direct Out
When connecting a mixer to a digital audio interface or multi-track recorder, you normally connect the Direct Out jack of each mixer channel to a track's input on the interface. For example, let's say your kick drum mic is connected to channel 1 of the mixer. If you wanted to record the kick drum to track 1, you would connect the channel 1 Direct Out to the track 1 input of the interface. You would then connect the channel 2 Direct Out to the track 2 input of the interface, etc. Using the Direct Outs in such a way takes each channel's signal post-fader and post-EQ and sends it straight to the recording device. This allows you to record that one instrument (and only that instrument) to its corresponding track on the recorder or in your DAW software.
But what if your mixer doesn't come equipped with Direct Outs? Many lower-priced mixers, or mixers designed more for stage use, do not. It's also common on many 16-channel mixers to only have Direct Outs on the first 8 channels. If your mixer doesn't have Direct Outs (or doesn't have enough of them), you could always use the Main L/R Outputs of the mixer, but there are only two of them. But the problem with this is that ALL of the channels in use will get mixed together and sent to those outputs, which is generally not what you want. If your mixer has Subgroup outs (or "buses"), you could use those, but on a 4-bus mixer, there are only, well–4 of them. So what's a guy to do if he wants to record each mixer channel to its own track? Fortunately, there's another alternative–the Insert Jack.
An Insert Jack is a TRS (Tip-Ring-Sleeve or 1/4? stereo) jack that is typically used to connect a signal processor to only affect a single mixer channel. An example would be a compressor or noise gate that might be connected through the Insert Jack of a mixer channel to only affect a single vocal mic. To use the Insert Jack in such a way, you need a "Y" cable with a stereo TRS plug on one end (connected to the Insert Jack) and two mono TS (Tip-Sleeve or 1/4? mono) plugs on the other end. One of the TS plugs is connected to the input on the signal processor and the other is connected to the output of the same device. So essentially, the Insert Jack creates a signal "loop" that both sends the signal for the channel out to an external signal processor and then returns it back to the mixer, all through a single jack (the Insert Jack). However, if you're not using an Insert Jack for its intended purpose (and you often will not), it has a handy second function–as a Direct Out.
There are a few different ways of using an Insert Jack as a Direct Out. First, you can use a standard TS to TS patch cable. Plug the cable all the way in to the Insert Jack. The only drawback here is that the signal is sent to the recorder from the Insert jack, but the signal is "interrupted" and is no longer sent to the mixer's main outputs. This may be okay for some recording situations, but in other cases, you will want the signal passed on through to the main outputs as normal, for monitoring purposes or for connection to a power amp and speakers in the case of a live concert.
The next option using a regular TS to TS cable is to only plug the cable in to the "first click" of the Insert Jack. This will tap the signal and send it straight out to the recorder, while still allowing it to pass on through to the mixer's main outputs. The only drawback to this is that if you don't get the cable plugged in just right (to only the first click), you may end up with either no signal to your recorder or no signal to the main outputs (or both).
So a better alternative than the "first click" or the "all-the-way-in" method is to use a special cable or adapter that both passes the signal for the channel to the send of the Insert Jack but still passes it on through to the mixer's outputs as normal. To do this, you can use a Stereo Plug to Mono Jack adapter with a normal mono TS to TS cable. Or you could buy a special Insert Direct Out cable adapter.
However, if you're like me, you like to keep your connections and cable runs as simple and clean as possible, in which case you don't like using adapters or plugging cables into cables. So the most elegant alternative is to use a specialized Insert Jack/Direct Out cable for just this purpose. Assuming that you have some very basic soldering skills, this cable is very easy to make, which I will now describe.
Start with a regular mono patch cable with TS plugs on both ends. Remove one of the plugs from the end with some wire cutters or tin snips. Now, solder a stereo TRS plug onto that end of the cable, shorting the Tip and Ring together, and connecting the shield to the Sleeve as normal. This will effectively send the signal to the output of the Insert Jack, while simultaneously returning it to the mixer, which will pass the signal on through to the Main outputs.
Some audio snobs might scoff at such a technique, saying that an Insert Jack wasn't designed to be used this way, and therefore it shouldn't be. However, some audio purists argue that for recording purposes, this method might actually be superior to using a Direct Out, because the signal path should be the shortest, cleanest, and most uncolored. The reason is that the signal is being sent directly from the preamp to the recorder, without going anywhere else. It's not passing through the EQ or even the fader, which could, in theory, color or degrade the signal.
Now, of course, like anything else, there are some pros and cons to using this technique. We've already covered the pros, so now for the cons. First, when using this technique, the only control that you have over the level of the signal being sent to the recorder is the Trim or Gain knob on your mixer. Because the Insert Jack is pre-fader, the fader becomes useless in terms of the signal being sent to the recorder. However, the fader will still control the level of the channel in the main mix. Second, when using this technique, you are bypassing the EQ, so if you like to use some EQ for preliminary shaping of the recorded track, you're out of luck. But in most cases, I don't use any EQ when tracking. I use the parametric EQ built into my DAW software for shaping the sound of my tracks after recording, so this isn't really a concern for me. Finally, if you're using the Insert Jack as a Direct Out, you can no longer use it as an Insert. So if you wanted to patch a Compressor into the channel to tame some peaks, you'd have to connect it another way (i.e.: Insert to Compressor to Recorder).
In conclusion, if you need to do some multitrack recording, but don't have a mixer that's equipped with Direct Outs (or enough of them), the Insert Jack makes a handy replacement. Or if you're an audio purist who wants the cleanest and shortest possible signal path between your mic and recorder, the Insert Jack may be the way to go.
About the Author
Jon Goad is a drummer, producer, and general music junkie. He's the owner and chief engineer of Silent Sky Studios and the drummer for the bands Immortal Soul and Soulfire.
When he's not having fun with music, Jon keeps the bills paid by working as a software developer for CUSI, a leading developer of software for the Utility industry. Jon lives in Northeast Arkansas with his wife Ashley and son Jack.
What is the cheapest way to make some 125 watt speakers work well on a laptop with only an audio jack input?
A cheap home-made amplifier or something. The speakers only have a positive and negative terminal input.
Well duh, all speakers have only a positive and negative terminal. You might be able to get it to work with an amplifier, but you are risking burning out the sound card pushing it that hard!
Jam With Your iPhone – PRS GuitarBud
The iPhone platform has quite a few apps for musicians, but what about the instrument itself? Now you can connect your electric guitar directly to your iPhone or iPod Touch (2nd gen or later) with the GuitarBud from PRS. It plugs into the iPhone’s audio jack and has connections for headphones [...] Filed in categories: Musical Gear , Spotlight Gadgets , iPhone, iPad, iPod related Tagged: Guitar ...
Thanks for visiting!
This entry was written by
admin, posted on
July 13, 2008 at 10:43 am, filed under
Vintage Computers and tagged
audio,
car,
input,
ipod,
jack,
jack input font,
jack input sizes,
video. Bookmark the
permalink. Follow any comments here with the
RSS feed for this post.
or leave a trackback:
Trackback URL.
